Why do I get a “socket error” message?
An error may result from having the speed test open in more than one browser tab or
window. The test may fail to complete and display the following message:
“A socket error occurred during the Upload test. Please try again later.”
To prevent this error, and get the most accurate test results, close all other browser tabs
and windows before running.
Why is the location I usually pick missing from the City list?
We first complete a latency test to our servers, and if a server does not respond
within a specified time frame, it is not included in the City list.
A slow response can be caused by latency or packet-loss between the client and server, or
particularly high Internet usage (during peak hours). Do try the test again in a little
while.
In which browsers does the Speed Test work best?
For best results, use the most recent version of your favorite browser. But at
minimum use Firefox 53, Chrome 59, Safari 10, IE 11, or Edge 13 or higher. If you
are unable to see Speed Test, though other content appears on the speed test page, check
your browser's security setting. Try lowering the setting from High to Medium-High, or even
a bit lower, to allow the broadband test application to load.
Why am I receiving “Could not connect to the Internet” errors when I am
connected?
In some cases, firewall and security software can prevent the test from running and
generate a "could not connect" error. Temporarily lowering the severity should allow the
broadband test to run. Be sure to turn it back on before leaving our website.
Why didn’t the test choose the server location nearest me?
Our Speed Test automatically detects the optimal server host location for
testing, which is not necessarily the closest server host. This is due to real-time
network circumstances like number of hops, or current traffic load on each test server.
Change the selection using the Change City drop down function directly underneath the Start
Test button.
Why is my speed lower than expected?
Several factors may slow your connection, resulting in lower-than-expected speeds. Try
these simple suggestions below. But if your slower speeds persist, contact your broadband
service provider to see if they can determine the issue.
- Be sure to stop any downloads or programs that may be using your connection while
running the test.
- When using a wireless connection, there may be wireless interference. Try using a wired
Ethernet connection instead.
- Try rebooting your modem or router and then running the test again.
What is “Throughput” and what factors affect my results?
There are many factors that impact your speed test results. Throughput problems in your
local area network, IP or access overhead, and network design all play a role. Please read
the definitions and examples below to learn more about these factors.
- Download
Download is a measure of how fast your connection delivers content to your computer
or local area network.
- Upload
Upload is the measure of how fast content is delivered from your computer or local
area network to others on the Internet.
For businesses or power-users, download and upload speed should match or at
least be very close. This is important for applications like VoIP, on-line gaming and
other interactive programs. Upload speed is even more important if you are operating a
server at your location. If achieving optimal upload speed is a concern, consider Dedicated
Internet Access.
- Kbps
Kbps transfer rate = kilobit per second transfer rate. There are 8 bits in a byte,
so we would divide kbps by 8 to get KB/sec transfer rate.
- Mbps
Mbps transfer rate = megabits per second transfer rate. 1000 kilobits equals one
megabit. One megabit per second equals 1 million bits per second. Mbps is the
industry-standard used by ISPs.
- MBps
MegaBytes per second. There are 8 megabits in one megabyte.
- Transfer Rate
- Transfer rate is speed at which data can be transmitted between devices. As files to
download become increasingly larger, the highest data transfer rate is most desirable.
- Throughput
Throughput is the maximum amount of communication or messaging that can be
transmitted through a communication channel during an elementary unit of time, usually,
in a second.
Depending on the type of channel, the addressing mechanism used in that channel,
the type of messages are being transmitted and how secure the transmission needs to
be—along with physical attributes like temperature, humidity and signal-to-noise
ratios—actual measured throughput will vary.
An Example of Throughput
You have Ethernet
8.0 Mbps service and need to transmit an email which is exactly 1MB in size You may
expect it will take exactly 1 second to transmit that message. But it will actually take
longer as the total information that needs to be transmitted is more than 1MB. The total
information is called Payload. The channel needs to not only transmit the
payload but also some addressing details like where it is coming from and where it is
destined to.
The device that sends this email will break down the message into smaller pieces and package
them into what are called IP Packets. The size of these packets is usually
determined by your Local Area Network. Some have smaller size, so the message will take more
IP Packets to transmit; while others may have larger size which needs fewer IP Packets. Each
IP Packet also contains an IP Header. This is where the information like
the source IP Address, the destination IP Address and additional information about the
payload is included. IP Header is usually 20 Bytes (160 Bits) long.
Assuming that this customer uses 100 Byte payload, each IP Packet will now be 120 Bytes long.
And that 1MB message will have to be broken down into 10,000 payload pieces. That means to
transmit the whole message the channel really needs to transmit about 1,200,000 Bytes or 1.2
MB or 9,600,000 bits. It will take at least 1.2 seconds to transmit all these bytes on this
8 Mbps service assuming that all these IP packets with the payload arrive without any errors
and not needing re-transmission. This is called IP Overhead.
Actual Throughput will always be less than line rate of the access service that is
communicated by your provider—and this is all based on IP Overhead only. Ethernet services
also have a Layer 2 or Ethernet Overhead. Other services may have ATM,
Frame Relay or other kinds of Overhead depending on the design. All of this may contribute
to a slower bandwidth throughput than what you are expecting.
Other frequent factors influencing throughput:
- The number of devices sharing the access circuit and the activity the other devices are
generating while the test is running
- A rogue LAN port that is clogging the LAN with transmission
- A leaky LAN port which degrades LAN performance
- LAN signaling issues which create a lot of packet re-transmission for the devices on the
LAN
- LAN Router with performance issues, low processing power or Deep Packet Inspection and
advanced security features like URL blocking enabled
- Wireless Access Points on the LAN side
- Distance (both geographical as well as number of hops) between the speed testing client
and the server
Why do I see a license expiration notice?
This notice is in place to protect our test from being stolen and run, mirrored, or
framed into another website.
To remove this notice:
Make sure you are going to https://www.speakeasy.net/speedtest/. We have
software in place to block the test from being used in any other domain.
Also, you may have an older version of the test cached in your browser. Clearing your cache
and Fusion Connect cookies should make the license expiration notice disappear.
How does security software and firewalls impact the test?
Our internet broadband test sends packets of empty data back and forth to your computer
in order to test your line speed. Since we are a third-party sending a receiving a tiny data
packet from your computer to perform the test, some ad block or security services interpret
this as an attack and act accordingly. Temporarily lowering the severity should allow the
speed test to work. Be sure to turn it back on before leaving our website.
How do I save my bandwidth test results?
Your most recent speed test results are saved in your Results History when tested on
desktop or tablet.
